中国组织工程研究Issue(52)：9035-9040,6.DOI:10.3969/j.issn.2095-4344.2013.52.016
数字散斑法测量加载100 N与500 N肱骨干骨折钢板固定下的位移
Displacement of steel plate for humeral fractures under the load of 100 N and 500 N measured using digital speckle method
摘要
Abstract
BACKGROUND:There is no unified measure of bone tissue mechanical property test at present. The study concerning traditional sensor for fracture displacement had some problems such as low precision, and high consumption cost. <br> OBJECTIVE:To measure the displacement of plate and screw after internal fixation for fracture of humerus using digital speckle method. <br> METHODS:A total of eight humeral specimens were taken. The steel plate fixation model in the humerus 1/2 was made. The specimens were fixed using eight-hole steel plate, and four screws were fixed on each end of fracture line. Five conditions of experimental model were designed for comparative analysis. Condition a:compression plate fixation group (not saw off, to simulate fracture healing). Condition b:on the basis of sawing off in condition a, one screw was removed on the proximal end. Condition c:on the basis of condition b, one screw was removed on the distal end. Condition d:on the basis of condition c, one screw was removed on the distal end. Condition e:on the basis of d, one screw was removed on the distal end. The screws were numbered No. 1-8 from top to bottom. That is, the screws on upper fracture line were numbered No. 1-4, and those on the lower fracture line were numbered No. 5-8. The specimens were instal ed on electronic universal testing machine, and loaded 100 N and 500 N. The displacement was calculated using the related software. <br> RESULTS AND CONCLUSION:Significant differences in total displacement were detected under different loads (F=49.155, P<0.001). With increased load, the total displacement of the fourth and fifth screws gradual y increased under five kinds of conditions. These indicated that the two screws on the two ends of the fracture line endured more stresses (stress concentration), and easily broke. It would be better to choose the screw with the screw diameter of 1-2.5 mm bigger than the present one in order to increase its stability to avoid the breakage of screws.关键词
骨关节植入物/骨关节与生物力学/肱骨干/骨折/钢板/内固定/生物力学/数字散斑法/国家自然科学基金Key words
fractures/humerus/internal fixators/biomechanics/fractures, stress分类
医药卫生引用本文复制引用
杨利萍,田明,周轶平,叶宏,李必俊,陈英杰..数字散斑法测量加载100 N与500 N肱骨干骨折钢板固定下的位移[J].中国组织工程研究,2013,(52):9035-9040,6.基金项目
云南省科技厅-昆明医科大学联合专项基金资助项目(2007C0043R，2011FZ098X)**；云南省教育厅科学研究基金立项资助项目(07Z10199，2010Y191，03Y508C，13000035，2010ZL004)*****；国家自然科学基金(31101616，31160425)**Funding:the Union Specific Foundation of Yunnan Province Technology Department and Kunming Medical University, No.2007C0043R,2011FZ098X** （2007C0043R，2011FZ098X）
the Scientific Research Project of Yunnan Province Education Department, No.07Z10199,2010Y191,03Y508C,13000035,2010ZL004***** （）
the National Natural Science Foundation of China, No.31101616,31160425** （）
