物理学报2017，Vol.66Issue(6)：318-330,13.DOI:10.7498/aps.66.067901
电子辐照电介质样品带电泄放弛豫特性研究
Transient characteristics of discharge of polymer sample after electon-beam irradiation
摘要
Abstract
Charging effect of dielectric material due to electron beam irradiation has a significant influence on the microdis-charge phenomenon of dielectric microwave component by multipactor. The discharge process caused by internal electron leakage can relieve this undesirable charging effect. In this paper, we study the transient discharge characteristics of a dielectric sample after being irradiated by electron beam through numerical simulation. Both the charging and discharg-ing processes of a dielectric sample are considered with a comprehensive model. The Monte-Carlo method is used to simulate the interaction between primary electrons and material atoms before the irradiation is interrupted, including elastic scattering and inelastic scattering. The elastic scattering is calculated with the Mott scattering model, and the inelastic scattering is simulated with the fast secondary electron model or Penn model according to electron energy. Meanwhile, the transport process of internal charges in the sample during the discharge period is simulated including the charge diffusion under the force of charge density gradient, the drift due to built-in E-field, and the trap caused by material defect. In this work, the discharge process is taken to begin at the very moment of charging reaching saturation, with the internal charges kept almost unchanged. A polymer material widely used in advanced component is considered in this work due to its remarkable charging effects. Distributions of internal charges of the sample during the discharge process are simulated, and influences of sample parameters, including sample thickness, electron mobility and trap density in the discharge process, are analyzed. The results show that internal charges move to the bottom of the sample during the discharging, leading to the surface potential reaching an ultimate state which is determined by trap density of the material. The position corresponding to the maximum internal charge density shifts towards the grounded bottom. Although a sample with a larger electron mobility means a faster discharge process, fewer free electrons in this sample result in less discharge quantity. The time constant of discharge process decreases with the increase of sample electron mobility in the form of similar linearity. Although a sample with a larger thickness can hold more internal charges, the increase of sample thickness may increase the distance of internal charges leak yet. Hence, the quantity of discharge first increases and then decreases with the increase of sample thickness. In addition, a larger trap density of a dielectric sample makes charge leak harder, resulting in a lower discharge quantity. Finally, the proportion of discharge quantity in saturated charge quantity decreases from 1 to 0 exponentially with the increase of sample trap density. As a conclusion, those sample parameters have their corresponding effects on discharge characteristics by means of different physical mechanisms. Sample electron mobility determines the discharge time constant obviously by affecting the electron transport speed. The sample thickness affects the discharge quantity by shifting the charging balance mode, and material defect impedes part of discharge quantity from trapping internal free electrons. This simulation method and results can help to recede the charging effect and estimate the evolution charging and discharging states of dielectric material during and after electron beam irradiation.关键词
带电泄放/电子辐照/介质材料/数值模拟Key words
discharge transient/electon-beam irradiation/dielectric material/numerical simualtion引用本文复制引用
封国宝,曹猛,崔万照,李军,刘纯亮,王芳..电子辐照电介质样品带电泄放弛豫特性研究[J].物理学报,2017,66(6):318-330,13.基金项目
国家自然科学基金重点项目(批准号:U1537211)、中国博士后科学基金(批准号:2016M602944XB)和空间微波技术重点实验室基金(批准号:9140C530101140C53231, 9140C530101150C53011)资助的课题. Project supported by the Key Program of National Natural Science Foundation of China (Grant No. U1537211), the China Postdoctoral Science Foundation (Grant No. 2016M602944XB), and the Foundation of National Key Laboratory of Space Microwave Technology, China (Grant Nos. 9140C530101140C53231, 9140C530101150C53011). （批准号:U1537211）
