农业工程学报2017，Vol.33Issue(13)：23-31,9.DOI:10.11975/j.issn.1002-6819.2017.13.004
内充气吹式玉米排种器工作性能EDEM-CFD模拟与试验
EDEM-CFD simulation and experiment of working performance of inside-filling air-blowing seed metering device in maize
摘要
Abstract
The qualified index of original inside-filling air-blowing seed metering device could reach above 85% when working pressure was more than 5 kPa. In order to reduce the working pressure and energy consumption of fan and optimize the working effect of inside-filling air-blowing seed metering device, the installation position of combined compressed air nozzle was adjusted at first to make it as close as possible to the hole. The qualified index of seed metering device was lower than 85% when the working pressure was 2.5 kPa, and qualified index was reduced when increasing or reducing working pressure. Thus it can be seen that the installation position of combined compressed air nozzle has a significant influence on the sowing effect of seed metering device. In this paper, the bonded particle model was used to model maize based on theory of discrete element method, and the coupling analysis method of EDEM-CFD was applied to simulate the influence of different air nozzle installation positions on the working performance of inside-filling air-blowing precision seed metering device. Installation positions of combined air nozzle of structural parameter, working pressure and working speed of working parameter were selected as experimental factors, particle filling limiting velocity and filling time were used as evaluating indicators, the orthogonal experiment was carried out to optimize working performance of seed metering device. The results of variance analysis of filling performance showed that the influence of three factors on filling limiting velocity was significant (P<0.05) and on filling time was not significant (P>0.05). The primary and secondary factors that affect the filling limiting velocity was working velocity > working pressure > installation position of combined air nozzle. A significant negative correlation (P<0.05) was found between filling limiting velocity and filling time and Pearson correlation coefficient was -0.785 (P=0.012). The results of variance analysis of cleaning performance showed that three factors had no significant (P>0.05) effect on qualified rate, reseed rate and leakage rate, but qualified index and filling limiting velocity were negatively correlated (P<0.05) when the combined air nozzle was in upper or lower position. The qualified index and filling limiting velocity was significantly positive correlation (P=0.01), the Pearson correlation coefficient was 1.00 and the significant level was 0.005. Therefore, in order to adapt to different working parameters of seed metering device, first of all, the installation position of combined air nozzle of structural parameters was optimized as the middle position. Bench test was performed to validate the simulation results. Double factor test of working pressure and installation positions of combined air nozzle was in progress when the working speed was 6 km/h, and compared with first generation seed metering device. Experimental results showed that the reseed rate of the installation position of combined air nozzle was lower than mille, but the upper position was opposite. The leakage rate of the middle installed position was better than the installation position of combined air nozzle and also was better than the installation position of combined air nozzle at the lower and upper positions. That is, the seed metering device has the best effect when the installation position of combined air nozzle was the middle, and the qualified rate of seed metering device was higher than 90% under all working pressure. The double factor test was carried out when the installation position of combined gas nozzle was at the middle with working speed of 4-12 km/h and working pressure of 3.0-7.0 kPa. Results showed that the seed metering device was easier to reseed at lower working pressure and lower working speed, it was easier to leakage at higher working pressure and higher working speed. On the whole, the qualified rate of seed metering device was higher than 90% under suitable working conditions.关键词
农业机械/计算机仿真/优化/精量排种器/充种性能/离散单元法Key words
agricultural machinery/computer simulation/optimization/precision metering device/filling performance/discrete element method分类
农业科技引用本文复制引用
韩丹丹,张东兴,杨丽,李克鸿,张天亮,王云霞,崔涛..内充气吹式玉米排种器工作性能EDEM-CFD模拟与试验[J].农业工程学报,2017,33(13):23-31,9.基金项目
国家自然科学基金资助项目(51375483) （51375483）
国家自然科学基金资助项目(51575515) （51575515）
现代农业产业技术体系建设项目-玉米-夏播区生产全程机械化(21226003) （21226003）
农业部土壤-机器-植物系统技术重点实验室资助项目 （）
