电工技术学报2024，Vol.39Issue(13)：4176-4187,4256,13.DOI:10.19595/j.cnki.1000-6753.tces.230618
基于光辐射强度的日盲紫外放电检测结果一致性校准方法
Consistency Calibration Method for Solar-Blind Ultraviolet Discharge Detection Results Based on Optical Radiation Intensity
摘要
Abstract
Solar-blind ultraviolet(UV)imaging technology has been widely used in the detection of external insulation discharge of electrical equipment,thanks to its strong anti-interference capability,long detection distance,non-contact operation,and accurate discharge location positioning.Existing research on UV discharge detection typically uses photon count or spot area as the UV detection parameters for assessing the external insulation condition of electrical equipment.However,for different models of UV imagers,the variations in their optical system structure and signal processing algorithms lead to significant differences in the numerical values of UV parameters obtained by the instruments,resulting in a lack of consistency and comparability.To address this issue,this study reveals the impact mechanisms of various factors such as temperature,humidity,pressure,and detection distance on the atmospheric transmission of solar-blind UV radiation and proposes a consistency calibration method for the detection results of UV imagers. Firstly,the impact characteristics of different factors such as temperature,humidity,pressure,and detection distance on the atmospheric transmission of solar-blind UV radiation were analyzed based on the MODTRAN model.An empirical calculation formula for the atmospheric transmittance of UV radiation in the wavelength range of 240 to 280 nm was obtained.It was found that,in weather conditions suitable for UV detection with humidity below 80％,humidity does not affect the transmission of UV radiation in the wavelength range of 240 to 280 nm.The impact coefficients of pressure,temperature,and detection distance on the atmospheric transmittance of UV radiation in the wavelength range of 240 to 280 nm are-0.018 8,0.000 1 and-0.001 4,respectively.Additionally,in the UV discharge detection of external insulation of electrical equipment,the discharge point was treated as a point source uniformly emitting light into the surrounding space,based on which a UV detection radiation transmission model was established. Then,a radiation metrology consistency calibration platform was constructed,and a consistency calibration method for UV detection results was proposed based on the UV detection radiation transmission model.The optical radiation intensity generated by the discharge point was selected as the standard parameter for the consistency calibration of UV detection results.Using this method,consistency calibration formulas were separately established for three different models of UV imagers.By converting the spot area measured by different models of UV imagers into the optical radiation intensity generated by the discharge point using the consistency calibration formulas,it ensures that the detection results of different models of UV imagers are consistent and comparable. Finally,based on the consistency calibration formulas for UV detection results,UV detection was performed on a rod-plate model of corona discharge using the three UV imagers.The relative standard deviations of the calculated optical radiation intensities for each UV imager were 0.080,0.087,and 0.098,respectively,and the relative standard deviation among all the calculated optical radiation intensities was 0.090.For UV detection of a deuterium lamp,the relative standard deviation of all the calculated optical radiation intensities was 0.063,with an average deviation of 5.78％from the actual optical radiation intensity of the light source(1 593μW/sr).The effectiveness of the consistency calibration method for UV detection results was demonstrated.关键词
紫外放电检测/辐射传输模型/辐射计量一致性校准平台/一致性校准方法/光辐射强度Key words
UV discharge detection/radiation transmission model/radiation metrology consistency calibration platform/consistency calibration method/optical radiation intensity分类
数理科学引用本文复制引用
李泳霖,黄世龙,刘云鹏,耿江海,杨家骏..基于光辐射强度的日盲紫外放电检测结果一致性校准方法[J].电工技术学报,2024,39(13):4176-4187,4256,13.基金项目
国家重点研发计划资助项目(2018YFF01011900). （2018YFF01011900）
