中国骨伤2026，Vol.39Issue(5)：445-451,7.DOI:10.12200/j.issn.1003-0034.20250130
按压和拔伸按压斜扳复合手法治疗腰椎间盘突出症的有限元分析
Finite element analysis of a combined manipulation technique involving pressing,traction-pressing,and oblique-pulling for lumbar disc herniation
摘要
Abstract
Objective To establish a lumbar spine model using the three-dimensional finite element method,simulate the pressing manipulation and the traction-pressing-oblique-pulling complex manipulation through mechanical simulation,to ana-lyze the mechanical effects of these two manipulations,and compare and discuss their biomechanical mechanisms and the dif-ferences in mechanical effects.Methods A typical lumbar disc herniation(LDH)patient was selected.Based on the patient's lumbar CT image data,a three-dimensional finite element model of the L4-L5 segment was constructed,focusing on in-depth analysis of a single sample.The reliability of the model was verified through mesh convergence analysis and comparison with literature.The stress and strain distribution in various tissue units of the L4-L5 segment,as well as the relative displacement distance between the intervertebral disc and the nerve roots,were observed during the application of the pressing manipulation and the traction-pressing-oblique-pulling manipulation.Results A three-dimensional finite element model of the L4-L5 segment based on imaging data from a patient with lumbar disc herniation was successfully constructed,and mechanical simulation analysis of the two manipulations was conducted.After applying the pressing manipulation,the stress was maximum at the an-terior part of the intervertebral disc and minimum at the herniated site;the strain was maximum at the herniated site and smaller anteriorly.The intervertebral disc exhibited overall forward strain,but backward strain also occurred at the anterior edge.The strain values were 0.097 for the annulus fibrosus and 0.153 for the nucleus pulposus.The intervertebral disc exhibited overall forward displacement:5.531 mm to the right on the X-axis,3.707 mm forward for the herniated disc on the Y-axis,and 2.031 mm upward for the herniated disc on the Z-axis.The left nerve root moved forward by 2.453 mm,while the right nerve root moved backward by 0.760 mm.After applying the traction-pressing-oblique-pulling complex manipulation,similar to the press-ing manipulation,the stress was maximum at the anterior part of the intervertebral disc and minimum at the herniated site.Re-garding disc strain,the posterior part exhibited the maximum strain,with smaller strain anteriorly.The intervertebral disc ex-hibited overall rightward strain and partial forward strain,with values of 0.751 for the annulus fibrosus and 0.587 for the nucle-us pulposus.The intervertebral disc exhibited overall forward and rightward displacement:8.594 mm to the right on the X-axis,5.409 mm forward for the left side on the Y-axis,while the right side(healthy side)moved backward,and 2.735 mm upward for the herniated part on the Z-axis.The left nerve root moved forward by 2.932 mm,while the right nerve root moved backward by 1.971 mm.Conclusion Both manipulations can enlarge the space between the intervertebral disc and the nerve roots,with the complex manipulation demonstrating superior biomechanical decompression effects.This study not only verifies the biome-chanical mechanisms of the two Traditional Chinese Medicine manipulations but also provides a reproducible and extensible three-dimensional finite element model for subsequent related clinical and mechanical research,possessing certain promotional value and practical guiding significance.关键词
腰椎/椎间盘移位/有限元分析/正骨手法/生物力学Key words
Lumbar vertebrae/Intervertebral disc displacement/Finite element analysis/Bone setting manipula-tion/Biomechanics分类
医药卫生引用本文复制引用
燕安迪,李帆冰,卢钰,李具宝..按压和拔伸按压斜扳复合手法治疗腰椎间盘突出症的有限元分析[J].中国骨伤,2026,39(5):445-451,7.基金项目
国家自然科学基金(编号:81460736 （）
81860862) （）
云南省科技厅科技计划项目(编号:202101AZ070001-178) （编号:202101AZ070001-178）
云南省教育厅科学研究基金项目青年人才基础研究(编号:2024J0513)National Natural Science Foundation of China(No.81460736 （编号:2024J0513）
No.81860862) （）
