| 注册
首页|期刊导航|表面技术|WC-14Co涂层在不同pH值模拟海水环境中的腐蚀磨损行为研究

WC-14Co涂层在不同pH值模拟海水环境中的腐蚀磨损行为研究

李明杰 舒文祥 余施佳 杨男 周尊媛 周龙龙 李政岭 周俊 蔡振兵

表面技术2026,Vol.55Issue(20):17-28,12.
✕
表面技术2026,Vol.55Issue(20):17-28,12.DOI:10.16490/j.cnki.issn.1001-3660.2026.20.002

WC-14Co涂层在不同pH值模拟海水环境中的腐蚀磨损行为研究

Tribo-corrosion Behaviors of WC-14Co Coatings in Simulated Seawater Environments at Different pH Values

李明杰 1舒文祥 2余施佳 1杨男 3周尊媛 1周龙龙 1李政岭 1周俊 3蔡振兵1

作者信息

  • 1. 西南交通大学 机械工程学院,成都 610031
  • 2. 中国空间技术研究院北京卫星制造厂有限公司,北京 100094
  • 3. 成都国营锦江机器厂,成都 610043
  • 折叠

摘要

Abstract

WC-Co coatings are widely used on critical components such as marine helicopter landing gears.In actual marine service environments,corrosion,wear,and their synergistic effects can drastically accelerate coating damage.Clarifying the evolution law of coating failures under complex marine conditions is an urgent need to ensure the long-term safe service of marine equipment. To investigate the tribo-corrosion behavior and failure mechanisms of WC-14Co coatings in simulated seawater environments at different pH values,a 3.5%NaCl solution was employed to simulate the marine environment.Tribo-corrosion behavior was examined in the 3.5%NaCl solution at pH values of 3,5,7,9,and 11 through electrochemical testing and sliding tribo-corrosion testing.A deep-field microscope,an optical 3D profilometer,and a scanning electron microscope were used to observe the cross-sections of the coating surface and the morphology of wear scars,and to obtain parameters such as 2D profiles and wear volume;A fully automatic Vickers hardness tester was used to measure the microhardness of the coating,and an X-ray photoelectron spectrometer was employed to analyze the corrosion products.For coating preparation,30CrMnSiA steel was used as the substrate.After thoroughly cleaning the substrate surface,it was subject to sandblasting.Using a JP-5000 flame spraying system with an oxygen flow rate of 49 m3/h,a kerosene flow rate of 22.5 L/h,a spraying distance of 330 mm,and a powder feed rate of 65 g/min,a WC-14Co coating approximately 250 μm thick was deposited onto the steel surface.For the electrochemical tests,a saturated calomel electrode(SCE)served as the reference electrode,a Pt electrode as the auxiliary electrode,and the test specimen as the working electrode.The pH was adjusted using 0.1 mol/L NaOH solution and 0.1 mol/L HCl solution.When it came to sliding tribo-corrosion testing,a ball-on-plate contact configuration was employed,with a 6-mm-diameter YG6 tungsten steel ball as the wear partner.The test parameters were set as follows:load of 150 N,test duration of 60 min,wear frequency of 5 Hz,and displacement amplitude of 4 mm. The results indicated that within the pH range of 3-7,both the self-corrosion current density and the wear volume of the coating decreased gradually as the pH increased.At pH=7,both the self-corrosion current density and wear volume of the coating reached their minimum values,at 1.073×10–5 A/cm2 and 6.1×10–2 mm3,respectively.When the pH ranged from 7 to 11,both the self-corrosion current density and wear volume of the coating gradually increased as the pH rose.The total volume loss due to corrosion and wear in different pH environments was primarily attributed to pure wear volume loss.The synergistic effect of corrosion and wear was significantly suppressed in neutral environments(accounting for only 4.78%),while it was substantially enhanced in acidic and alkaline environments,reaching as high as 34.14%in strongly alkaline environments.The failure mechanism of the coating in acidic,neutral,and weakly alkaline environments is the dissolution of the Co binder phase and slight oxidation of the WC hard phase,whereas in strongly alkaline environments,the failure mechanism is a dual failure involving the dissolution of the Co binder phase and the erosion of the WC hard phase.

关键词

WC-14Co涂层/腐蚀磨损/pH值/协同效应/失效机理

Key words

WC-14Co coating/tribo-corrosion/pH value/synergistic effect/failure mechanism

分类

矿业与冶金

引用本文复制引用

李明杰,舒文祥,余施佳,杨男,周尊媛,周龙龙,李政岭,周俊,蔡振兵..WC-14Co涂层在不同pH值模拟海水环境中的腐蚀磨损行为研究[J].表面技术,2026,55(20):17-28,12.

基金项目

四川省科技计划项目(2022ZYD0029) (2022ZYD0029)

国家重点研发计划项目(2024YFC3908103)Supported by the Sichuan Provincial Science and Technology Program(2022ZYD0029) (2024YFC3908103)

National Key R&D Program of China(2024YFC3908103) (2024YFC3908103)

表面技术

1001-3660

访问量0
|
下载量0
段落导航相关论文