| 注册
首页|期刊导航|重型机械|钨合金静液挤压工艺参数模拟与试验研究

钨合金静液挤压工艺参数模拟与试验研究

王好 杨建 张雷 张君 罗远新 王勇勤 罗洋

重型机械Issue(5):37-47,11.
✕
重型机械Issue(5):37-47,11.

钨合金静液挤压工艺参数模拟与试验研究

Simulation and experimental study on process parameters of hydrostatic extrusion of tungsten alloy

王好 1杨建 2张雷 3张君 4罗远新 3王勇勤 1罗洋1

作者信息

  • 1. 重庆大学 机械与运载工程学院,重庆 400030
  • 2. 重庆大学 机械与运载工程学院,重庆 400030||中国重型机械研究院股份公司 金属成形技术与重型装备全国重点实验室,陕西 西安 710018
  • 3. 重庆大学 机械与运载工程学院,重庆 400030||重庆大学 国家卓越工程师学院,重庆 401135
  • 4. 中国重型机械研究院股份公司 金属成形技术与重型装备全国重点实验室,陕西 西安 710018
  • 折叠

摘要

Abstract

To address the problems of high forming pressure,narrow process window,and property matching in ultra-high-pressure hydrostatic extrusion of high-strength tungsten alloy,93W alloy bars were investigated through numerical simulation and process experiments.An axisymmetric finite element model was established,and the effects of extrusion speed,extrusion ratio,friction coefficient,and die angle on extrusion pressure as well as internal stress-strain fields were systematically analyzed using a single-factor method.Process verification was then carried out on a modified ultra-high-pressure hydrostatic extrusion test platform.The results show that extrusion speed has a limited effect on peak pressure,but low speed causes pressure fluctuations,while the process becomes stable when v≥2 mm/s.The extrusion pressure increases with extrusion ratio and is approximately linear with the natural logarithm of the extrusion ratio;for tungsten alloy,the extrusion ratio should be controlled below 2 considering equipment capacity and safety.When the friction coefficient increases from 0 to 0.2,the extrusion pressure rises by about 400 MPa,indicating that interface lubrication is essential for load reduction.The pressure first decreases and then increases with die angle,and an angle around 40° is preferred.The hardness of the products increased from 28 HRC to 40-47 HRC after extrusion,with significantly improved tensile strength.Heat treatment further improved the impact toughness(from 8.7 J/cm2 to 19.35 J/cm2).This study provides a basis for process optimization and equipment parameter selection for ultra-high-pressure hydrostatic extrusion of tungsten alloys.

关键词

钨合金/静液挤压/工艺参数/有限元模拟/挤压压力/力学性能

Key words

tungsten alloy/hydrostatic extrusion/process parameters/finite element simulation/extrusion pressure/mechanical properties

分类

矿业与冶金

引用本文复制引用

王好,杨建,张雷,张君,罗远新,王勇勤,罗洋..钨合金静液挤压工艺参数模拟与试验研究[J].重型机械,2026,(5):37-47,11.

基金项目

金属成形技术与重型装备全国重点实验室开放基金(B2408100.W11) (B2408100.W11)

重型机械

1001-196X

访问量0
|
下载量0
段落导航相关论文